-->
Log In | View Cart ( 0 ) | Site Map
channel partners
hypertherm
Kjellberg
Burnyamc
M/S. Hypertherm USA

Powermax ® systems

powermax
    Powermax30 Powermax45 Powermax1000 Powermax1250 Powermax1650
Handheld cut capacity Recommended 1/4" (6 mm) 1/2" (12 mm) 3/4" (19 mm 7/8" (22 mm) 1-1/4" (32 mm)
Maximum 3/8" (10 mm) 3/4" (19 mm) 1" (25 mm) 1-1/8" (29 mm) 1-1/2" (38 mm)
Severance 1/2" (12 mm) 1" (25 mm) 1-1/4" (32 mm) 1-1/2" (38 mm) 1-3/4" (44 mm)
Mechanized pierce capacity Maximum Not applicable 3/8" (10 mm) 1/2" (12 mm) 5/8" (16 mm) 3/4" (19 mm)
Gouge capacity Metal removed per hour
depth x width
Not applicable 6.2 lbs (2.8 kg) 11 lbs (4.9 kg) 15 lbs (6.8 kg) 24 lbs (10.8 kg)
Output current (amps)   15 - 30 20 - 45 20 - 60 25 - 80 30 - 100
Dimensions depth x width x height 14.0 x 6.6 x 12.0" 16.8 x 13.7 x 6.8" 23.1 x 10.7 x 19.6" 23.1 x 10.7 x 19.6" 26.4 x 16.8 x 25.8"
  (356 x 168 x 305 mm) 426 x 348 x 172 mm) (586 x 271 x 498 mm) (586 x 271 x 498 mm) (671 x 427 x 655 mm)
 

Mechanized systems

Mechanized
      MAX200 HySpeed HSD130 HPR130XD HPR260XD HPR400XD
Capacity Mild steel Dross free 25 mm (1") 16 mm (5/8") 16 mm (5/8") 32 mm (1-1/4") 38 mm (1-1/2")
Production (pierce) 25 mm (1") 25 mm (1") 32 mm (1-1/4") 38 mm (1-1/2") 38 mm (1-1/2")
Severance (edge starts) 50 mm (2") 38 mm (1-1/2") 38 mm (1-1/2") 64 mm (2-1/2") 80 mm (3.2")
Stainless steel Production (pierce) 25 mm (1") 20 mm (3/4") 20 mm (3/4") 32 mm (1-1/4") 45 mm (1-3/4")
Severance (edge starts) 50 mm (2") 25 mm (1") 25 mm (1") 50 mm (2") 80 mm (3.2")
Aluminum Production (pierce) 25 mm (1") 20 mm (3/4") 20 mm (3/4") 25 mm (1") 45 mm (1-3/4")
Severance (edge starts) 50 mm (2") 25 mm (1") 25 mm (1") 50 mm (2") 45 mm (1-3/4")
* Note: Take care in comparison: competitors often show maximum cutting speeds rather than speeds that deliver the best cuts, as shown above. Cut speeds listed above deliver best cut quality for a given process, but cut speeds can be up to 50% faster.
** ISO 9013 is a standard that defines cut quality of thermally cut parts. The lower the range (range 1 is the lowest), the smaller the angle on the cut face. Cut angle in range 4 is better than in range 5.
 

Computer numerical controls (CNC) hardware

cnc
    Powermax30 Powermax45 Powermax1000 Powermax1250 Powermax1650
Drive amplifiers supported Analog SERCOS Analog SERCOS Analog, 250 W (internal) SERCOS
Maximum axes 6 12 4 12 4 12
Maximum inputs and outputs 48/48 512/512 12/12 512/512 12/12 512/512